Moog Videolarm WS6S-50NF-X2 Especificaciones descargar pdf

PRODUCT INSTRUCTIONS

INSTALLATION PREPARATION

1. Choose an appropriate corner location. The WS6 can be

mounted at any height in a corner.

2. Complete all wire and conduit runs prior to installation of

the housing.

REVISION DATE: 11-11-2010

Depending on the voltage being used, refer to one of the formulas

below to select the correct power supply for cameras connected

in parallel (positive to positive, negative to negative):

Total current for a 12 VDC system:

TOTAL CURRENT = (350mA x total number of cameras)

Total current for a 24 VAC system:

TOTAL CURRENT = (202mA x total number of cameras)

VOLTAGE CURRENT POWER

12 VDC 350mA 4.2W

24 VAC 202mA 4.8W

CABLE AND POWER GUIDELINES

(Detailed info on Page 11)

This chart shows the proper current needed for power supplies for

Warrior Series cameras. Use Class 2 Power only. Input voltage

must be between 12-28 VDC or 15-28 VAC.

81-IN5219 WARRIOR 6

WS6

INSTALLATION PROCEDURE

1. Using the security tool provided, loosen the (3) 10-32 security

fasteners and remove the face plate (Figure 1).

4. Feed the wiring through the conduit knockout. A clamp

connector is included should you desire to use it. Install

the connector so that the nut is on the outside of the housing.

Be sure the hole in the wall is large enough to accommodate

the nut. Tighten the nut securely, making sure that the screw

heads on the connector are in an easy to reach position,

then feed the wiring through the clamp connector.

5. Mount the back box to the wall using appropriate hardware

(not provided).

NOTE: If the clamp connector was used, tighten the screws

at this time. Make sure enough wire is inside

the back box to complete the wiring process.

2. Place the back box into position and mark the four mounting

holes (Figure 2).

3. If you're using the top conduit knockout (Figure 2) REMOVE

THE CAMERA AND BRACKET TO PREVENT DAMAGE.

If using one of the side conduit knockouts it's not necessary to

remove the camera and bracket; however, use caution.

Mounting

Holes

Figure 1

Top conduit knockout behind camera CAMERA MUST BE

REMOVED BEFORE USING

Mounting Holes

Figure 2

TABLE OF CONTENTS

Cable and Power Guidelines 1, 11

Installation Preparation 1

Installation Procedure 1

Wiring 2

Optional Warrior Test Monitor Cable 2

Camera Bracket Setup 2

Camera Focusing 3

Camera Settings 3

Completion of Installation 5

Window Guard™ Replacement 5

NVT Instructions 5

Warranty Information 7

Service and Safeguard Information 8

Troubleshooting 9

1 2 3 4 5 6 ... 11 12

Indice de contenidos

Pagina 1 - 81-IN5219 WARRIOR 6

PRODUCT INSTRUCTIONSINSTALLATION PREPARATIONINSTALLATION PREPARATION1. Choose an appropriate corner location. The WS6 can be mounted at any heigh

Pagina 2 - WIRING (Figure 3)

- 10 -Depending on the voltage being used, refer to one of the formulas below to select the correct power supply for cameras connected in parallel (po

Pagina 3 - CAMERA SETTINGS

- 11 -LIMITED WARRANTYFOR VIDEOLARM INC. PRODUCTSVIDEOLARM INC. warrants this Product to be free from defectsin material or workmanship,as follows:PRO

Pagina 4 - ADDENDUM 1

- 12 -Product Registration/WarrantyThank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the

Pagina 5 - Wiring Notes

- 2 -CAMERA BRACKET SETUP8. To adjust the camera bracket, loosen the two thumb screws (Figure 6). When the desired focus and location are achiev

Pagina 6 - DO NOT OPEN

- 3 -Figure 7CAMERA FOCUSING (Figure 7)1. The camera is factory equipped with a 3.6mm xed lens. A 2.5mm lens is also provided. To remove the 3

Pagina 7

- 4 -WINDOW GUARD™ PAINT SHIELD REPLACEMENTYour Warrior 6 comes with a replaceable Window Guard™ paint shield to protect the front plate window from v

Pagina 8 - TROUBLESHOOTING

250 ft  3  4  5  8  13 W300 ft  4  5  6  10  16 W400 ft 5  6  8  13  21 W500 ft  6  8  10  16  26 W600 ft 8  10  12  1

Pagina 9 - NVT TROUBLESHOOTING

- 6 -IMPORTANT SAFEGUARDS SAFETY PRECAUTIONSUNPACKINGSERVICE1 Read these instructions.2 Keep these instructions. 3 Heed all warnings 4 Fo

Pagina 10 - CABLE AND POWER GUIDELINES

654321WS6 - Exploded Diagram and Replacement Parts ListPart Number Description1 RPWS6010 WARRIOR 6 FACE PLATE FASTENER KIT2 RPWS6020 WARRIOR 6 FRONT P

Pagina 11 - LIMITED WARRANTY

Power SupplyPower APower BCameraAssemblyPrimaryPowerVideo SignalVideo ShieldMonitor- 8 -(Ground Return)Figure A Ground LoopTROUBLESHOOTINGIf you exp

Pagina 12 - Online Option 2: Mail-In

AC VoltmeterCamera MonitorBridge TapNV-213ANV-213A- 9 -NVT TROUBLESHOOTINGIf you are experiencing problems, attempt to simplify your setup. Test each