Moog Videolarm QFDWT4-70NA Especificaciones descargar pdf (Pagina 5)

- 5 -

250 ft

3 4 5 8 13 1

300 ft

4 5 6 10 16 1

400 ft

5 6 8 13 21 1

500 ft

6 8 10 16 26 1

600 ft

8 10 12 19 31 1

800 ft

10 13 16 25 42 1

1000 ft

13 16 20 32 52 1

1250 ft

16 20 25 40 65 1

1500 ft

19 24 30 48 78 1

1750 ft

23 28 35 55 91 1

2000 ft

26 32 40 63 104 1

2500 ft

32 40 49 79 131 1

3000 ft

39 48 59 95 157 1

3500 ft

45 56 69 111 183 1

4000 ft

52 64 79 127 209 1

5000 ft

65 80 99 158 261 1

6000 ft

78 95 119 190 313 1

8000 ft

104 127 158 253 418 1

Unshielded Twisted-Pair Wire Gauge (AWG)

Cable

Distance

2422201918

Unshielded Twisted-Pair Wire Gauge (AWG)

Distance

2422201918

Unshielded Twisted-Pair Wire Gauge (mm)

Distance

0.50.60.70.81.0

3 4 5 8 13 1

4 5 6 10 17 1

5 7 8 13 21 1

6 8 10 16 26 1

9 10 13 21 34 1

13 16 19 31 51 1

17 21 26 42 69 1

21 26 32 52 86 1

26 31 39 62 103 1

32 39 49 78 129 1

38 47 58 94 154 1

43 52 65 104 171 1

51 63 78 125 206 1

64 78 97 156 257 1

77 94 117 187 309 1

102 125 156 249 411 1

Cable

75 m

100 m

125 m

150 m

200 m

300 m

400 m

500 m

600 m

750 m

900 m

1000 m

1200 m

1500 m

1800 m

2400 m

75 m

100 m

125 m

150 m

200 m

300 m

400 m

500 m

0 m

750 m

900 m

1000 m

1200 m

1500 m

1800 m

2400 m

3 5 6 9 13 1

4 7 9 12 18 1

6 8 11 15 22 1

7 10 13 18 27 1

9 13 17 24 36 1

13 20 26 36 54 1

18 27 35 48 72 1

22 33 43 60 90 1

26 40 52 72 108 1

33 50 65 89 135 1

40 60 78 107 162 1

44 66 86 119 179 1

53 80 104 143 215 1

66 100 130 179 269 1

79 120 155 215 323 1

106 159 207 286 431 1

Wiring Notes

Wire — What to DO

1. DO use point-to-point Unshielded Twisted Pair wire, gauge 24 or

thicker, stranded or solid, Category 2, 3, 4, or 5.

2. The video signal may co-exist in the same wire bundle as other

video, telephone, data, control signals, or low-voltage power. It

is also OK to run NVT video signals in or near electromagnetic

fields (in accordance with National Electrical Code, local, or other

local safety requirements).

3. DO measure the wire distance. Use only transceivers that are

designed for that distance.

4. DO make sure the pair of wires carrying the video signal is sent

as a twisted pair (e.g. the blue-white/white-blue wires twisted

together as a pair), not a “split-pair” (e.g. blue-white conductor,

part of one pair/orange-white conductor, part of another pair).

Wire — What NOT to DO

1. DO NOT USE SHIELDED TWISTED PAIR WIRE. It will severely

degrade the distance performance. Short runs may be used with

some signal degradation (for example elevator traveler cables).

Multi-pair wire with an overall shield is OK.

2. DO NOT USE UN-TWISTED WIRE. It will reduce the NVT

product’s inherent interference immunity.

3. DO NOT allow your installation to have “bridge-taps”, loading

coils, talk-battery, or MOV type protectors. Bridge-taps are where

a twisted pair is connected to two twisted pairs (such as an

extension phone at home). Bridge-taps cause reflections as the

signal propagates, resulting in “ghosts” in the video image, and

are to be avoided.

4. If the phone company is providing the cable runs between

buildings, make sure it’s “dry copper” i.e. it should have none

of the following: dial-tone, 48 volts, loading coils, bridge-taps,

switching, or long paths to the phone company’s central office

and back.

5. Due to near-end crosstalk, DO NOT send a transmit and a

receive signal in the same wire bundle. Exceptions: Less than

1,000 ft (300m), or Category 5 cable, up to 2,000 ft (600m) are

OK.

6. DO NOT send “Up-the-Coax” Pan/Tilt/Zoom signals through

active (amplified) NVT transceivers.

Measure your wire distance

Note: All NVT quoted distance specifications include any coax in the

run. It is recommended that the wire distance be measured to ensure

that the capability of the NVT product is correct.

Wire resistance may be measured with an ohm-meter by shorting

the two conductors together at the far end, and measuring the loop-

resistance out and back. Compare your readings with the charts in

the next column.

7. For safety, never put NVT signals in the same conduit as

high-voltage wiring.

8. WARNING — to reduce a risk of fire or electrical shock, do

not expose this product to rain or moisture.

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Moog Videolarm QFDWT4-70NA Especificaciones Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Cámaras De Seguridad Moog Videolarm QFDWT4-70NA